Products
Plug-in switch-GN30-12
The disconnector type GN30-12 is a rotating contact blade for indoor high-voltage switchgear, suitable for power systems with 50 Hz alternating current and 12 kV rated voltage. It is mainly used to open and close circuits under no-load conditions to achieve electrical isolation. Its compact design is suitable for installation in high-voltage switchgears, improving distribution system space utilization
Description
marker
Product Details
The GN30-12 type disconnector is a rotating contact blade for indoor high-voltage switchgear, suitable for power systems with 50 Hz alternating current and 12 kV rated voltage. It is mainly used to open and close circuits under no-load conditions to achieve electrical isolation. Its compact design is suitable for installation in high-voltage switchgears, improving distribution system space utilization
Support manual control, control the movement of the blade by turning the handle.
Functions
Provide visible break points to ensure safe isolation during maintenance.
Low power circuits such as charging current and voltage transformers for splitting and combining buses.
Applications
- Built into indoor substations, switchgears and high-voltage switchgears.
- Places not subject to strong vibration, chemical corrosion and explosion hazards.
Precautions
- Working with the load is strictly prohibited: opening and closing must be done after the circuit breaker has been completely switched off.
- Maintenance requirements: Regularly check the condition of the contacts, the cleanliness of the insulators and the flexibility of the mechanism.
GN30-12 type disconnect switches are widely used in electrical isolation scenarios of indoor power systems due to their compact design and reliable operation. Selection should be based on current level, installation conditions and functional requirements
contact us
Related Popular Products
Pin insulator 10 kV
The product includes a fiberglass and epoxy resin rod, a silicone rubber protective skirt, and metal connectors (such as fittings). Process Features: The silicone rubber protective skirt is made by injection molding to improve the electrical insulation of the interface; the metal reinforcement is connected to the core by crimping to provide flexural strength.
Plug-in connection at the rear
Appearance The overall design is T-shaped. The large port at the top is used to connect the main cable, and the perpendicular side port is used to output the branch cable. The bottom port is usually equipped with a special sealing or connecting component to ensure a reliable connection and sealing of the cable system.
Plug-in switch-GN30-12D
GN30-12D is a special model of GN30-12: built-in grounding blade, increasing the safety of the grounding system. Supports manual control, control the movement of the blade by turning the handle.
Disconnector-(H)GW5-126kV(138kV)
GW5 Isolation Switch 126-138KV Isolation Switch (also known as Disconnector) Rated Voltage: 126KV, Suitable for Three-Phase AC 50Hz High Voltage Transmission System, Support Outdoor Operation in Difficult Environment
Disconnector-(H)GW4-72.5kV
GW4 Isolation Switch 72.5kV Isolation switch (also known as disconnector) 72.5kV, suitable for high voltage 50/60Hz three-phase AC transmission system. Insulation characteristics: lightning impulse withstand voltage 185 kV (to ground), power frequency withstand voltage 100 kV (to ground), higher value of failure withstand voltage, ensuring the reliability of electrical insulation after tripping.
Support insulator 110 kV
110 kV, suitable for high-voltage transmission and conversion systems of three-phase alternating current with a frequency of 50 Hz, ensuring long-term outdoor operation. The rod core is made of glass fiber reinforced resin, and the protective skirt is made of high temperature vulcanized silicone rubber, which is 50% lighter than porcelain and resistant to salt fog, ultraviolet radiation and chemical corrosion. Sealing the ends of the rod using the crimping method prevents moisture from entering the contact area of the rod core.
End coupling ready for installation 6 kV
Using rubber and polymer composite materials with elastic memory function, it can achieve cold shrinkage installation process of 24; Temperature resistance range covers 70℃ to 200℃, with good fire resistance and adapt to various working conditions
disconnector-HJDW6-0.5630~2000
HJDW6 series is a low voltage fused isolation switch designed specifically for 50Hz AC distribution lines with rated voltages of 500V and below. Mainly used for short circuit, overload, open circuit and short circuit protection under no-load conditions on the low voltage side of transformers
Insulator with 1/2 eye 24 kV
Connection Design: Single Eye/Double Eye Configuration: Suitable for hanging or tension insulators, double eye design is mainly used for hanging wires, and one eye for fixed ends.
Support insulator 220 kV
220KV Composite Column Insulators are high voltage insulation equipment made of silicone rubber as the core combined with fiberglass rods and metal accessories, specially designed for power transmission lines and substations.
Support insulator 66 kV
66 kV, suitable for three-phase high voltage AC transmission systems with a frequency of 50 Hz. The design consists of a fiberglass rod and a silicone rubber protective umbrella, which is 50% lighter than porcelain and resistant to UV radiation and salt spray.
Heat-shrinkable end coupling 24 kV
24kV heat shrink cable terminal is a key component used to connect the terminals of 24kV voltage level power cables, mainly to achieve cable terminal sealing, insulation protection and voltage control
Disconnectors 24 kV Russia
Components: Consists of base, rotating shaft, frame, insulated contact blade, contacts and connecting structure, and other components using three-phase parallel.
Fuse-(H)RW5-35 kV
HRW5 series is a 35kV open high voltage fuse specially designed for short circuit and overload protection of power lines and transformers, with open circuit and low load current line opening and closing functions.
Fuse-(H)RW10-15kV
Mainly used for short circuit and overload protection in 10kV distribution systems, with rated load current switching function, suitable for protecting overhead lines and distribution transformers
Switch-(H)GW4-15
GW4 series disconnect switches are outdoor high-voltage switchgears widely used in power systems, mainly for voltage isolation and safety protection in electrical equipment maintenance.
