Products
disconnector-HJDW6-0.5630~2000
HJDW6 series is a low voltage fused isolation switch designed specifically for 50Hz AC distribution lines with rated voltages of 500V and below. Mainly used for short circuit, overload, open circuit and short circuit protection under no-load conditions on the low voltage side of transformers
Description
marker
Product Details
HJDW6 series is a low voltage fused isolation switch designed specifically for AC distribution lines with a frequency of 50Hz, rated voltage 500V and below. Mainly used for short circuit, overload, open circuit and short circuit protection under no-load conditions on the low voltage side of transformers
Functions
Provide physical isolation of circuits, provide visible break points and ensure safe service.
They open and close transformers or lines in no-load mode and are responsible for performing short circuit and overload protection tasks.
Typical Applications
- Power distribution system: protecting the low voltage side of the transformer and switching lines.
- New energy projects: outdoor low-voltage distribution circuits such as wind power and photovoltaics.
- Industrial scenario: Isolation of power supply to low voltage equipment without risk of explosion
HJDW6 series circuit breakers are widely used in low voltage distribution systems due to their compact design, high protection level and fuse protection function. The selection must be fully evaluated based on voltage and current levels, pollution levels, and functional requirements.
contact us
Related Popular Products
Disconnectors 24 kV Russia
Components: Consists of base, rotating shaft, frame, insulated contact blade, contacts and connecting structure, and other components using three-phase parallel.
Disconnector-(H)GW5-126kV(138kV)
GW5 Isolation Switch 126-138KV Isolation Switch (also known as Disconnector) Rated Voltage: 126KV, Suitable for Three-Phase AC 50Hz High Voltage Transmission System, Support Outdoor Operation in Difficult Environment
Support insulator 66 kV
66 kV, suitable for three-phase high voltage AC transmission systems with a frequency of 50 Hz. The design consists of a fiberglass rod and a silicone rubber protective umbrella, which is 50% lighter than porcelain and resistant to UV radiation and salt spray.
Suspended insulator 110 kV
110 kV, suitable for high-voltage 50 Hz three-phase AC transmission systems, ensuring long-term outdoor operation. In typical applications, the rod core is made of glass fiber reinforced resin and the protective skirt is made of vulcanized high temperature silicone rubber, reducing weight by 50% compared to traditional porcelain. The technology of crimping the ends and double sealing eliminates the risk of breakdown of the connection between the core and the shell.
Lightning rod 24 kV
Type classification: 24kV lightning rod is mainly composed of zinc oxide composite external type, which is suitable for lightning surge protection of distribution systems and substation equipment. Performance standards: Must comply with GB/T 18802.1 national standard and IEC60099-4 standard, and some models are suitable for special environmental requirements such as high pollution and icing
Lightning rod 10 kV
Type classification: 10kV lightning rods mainly include power plant type, distribution type, and removable type, among which zinc oxide lightning rods have become the main ones due to their non-linear current-voltage characteristics.
Cold-shrinkable end coupling 110 kV
Formed by injection vulcanization of silicone rubber or ethylene propylene rubber, pre-expanded and lined with a spiral support structure, tightly adheres to the cable interface by elastic retracting force after installation, forming a strong seal. Adapt to high voltage level, suitable for 110kV – 220kV XLPE cables, with temperature resistance range from -50℃ to +90℃
Cold-shrinkable end coupling 24 kV
The main function of 24kV cold shrink cable terminal is to ensure safe and reliable cable operation, prevent damage caused by thermal expansion and contraction, and ensure good sealing and insulation protection. The cold shrink cable terminal uses cold shrink voltage control tube, suitable for voltage levels from 10kV to 35kV.
Support insulator 110 kV
110 kV, suitable for high-voltage transmission and conversion systems of three-phase alternating current with a frequency of 50 Hz, ensuring long-term outdoor operation. The rod core is made of glass fiber reinforced resin, and the protective skirt is made of high temperature vulcanized silicone rubber, which is 50% lighter than porcelain and resistant to salt fog, ultraviolet radiation and chemical corrosion. Sealing the ends of the rod using the crimping method prevents moisture from entering the contact area of the rod core.
Middle cold-shrinkable coupling 33 kV
Suitable for 33kV AC three-phase systems, designed using double-layer cold-shrink silicone tube with built-in stress cone to distribute the electric field evenly, local discharge capacity ≤ 10 pC; The connection of conductors is carried out by crimping, and the copper tube is suitable for cable cross-sections from 50 to 1000 mm².
Cold-shrinkable end coupling 33 kV
Insulation protection: Cold shrink cable terminal uses cold shrink voltage control tube, which can effectively insulate the cable from the external environment, prevent the cable from being damaged by external factors, and ensure good insulation protection
Cold-shrinkable end coupling 6 kV
6KV Cold Shrink Cable Terminal is a cable accessory that is made of elastic materials (such as silicone rubber or EPDM), sealed and insulated by elastic compression force. Its main components include cold shrink tension control tube, insulating tube, branch coupling, etc. Adaptive shrinkage is achieved by removing the inner support spiral tape to match the cable interface
Fuse-(H)RW5-35 kV
HRW5 series is a 35kV open high voltage fuse specially designed for short circuit and overload protection of power lines and transformers, with open circuit and low load current line opening and closing functions.
Disconnector-(H)GW4-220kV
GW4-220 isolation switch is an open AC isolation switch designed specifically for 220kV high voltage power systems, mainly used for circuit switching and electrical isolation of equipment under no-load conditions.
Disconnector-(H)GW4-40.5kV
Ratings Voltage level: 40.5KV, suitable for three-phase AC 50Hz 24 Current specifications: Cover configurations such as 630A, 1250A, 2000A, etc., to meet different load requirements. Insulation characteristics: Frequency withstand voltage 95 kV (to ground), lightning impulse withstand voltage 185 kV (to ground), in accordance with IEC standards.
End coupling ready for installation 6 kV
Using rubber and polymer composite materials with elastic memory function, it can achieve cold shrinkage installation process of 24; Temperature resistance range covers 70℃ to 200℃, with good fire resistance and adapt to various working conditions
