Products
Suspended insulator 10 kV
10kV suspension insulator is a key component used to support wires and provide insulation in power systems, mainly applied in key assemblies such as tension rods and corner rods of overhead power lines.
Description
marker
Product Details
10kV suspension insulator is a key component used to support wires and provide insulation in power systems, mainly applied in key assemblies such as tension rods and corner rods of overhead power lines.
Methods of application and maintenance
Applications of Tension Rods: Mainly used on 10kV transmission lines to withstand wire tension and isolate potential, requiring regular inspections for aging, contamination and damage.
Maintenance Process: Includes steps such as disconnecting power, checking electrical equipment, replacing damaged insulators, etc. Working at height requires safety precautions (such as grounding wires, safety harnesses) to ensure safe operation.
contact us
Related Popular Products
“+” type connector
A cross-shaped removable contact tip is a device designed to quickly connect and disconnect pipelines without the use of complex tools. Connection and disconnection of the piping system is accomplished by simple insertion and removal.
Middle cold-shrinkable coupling 66 kV
Rated voltage: 66 kV, lightning impulse withstand voltage ≥ 250 kV, power frequency withstand voltage ≥ 125 kV (continuously for 30 minutes); partial discharge capacity ≤ 5 pC (complies with IEC 60840 standard).
Plug-in assembly
The European connector head (a combination of front and rear plugs) is a cable splitter, which is a type of cable accessory.
Switch-(H)GW1-15
Isolation switch GW1 is a switching device mainly used for 15kV transmission lines, designed for “power supply isolation, switching, connection and disconnection of small current circuits”, without arc suppression function.
Wind fuse-HRW12-35kV
A removable fuse is a specially designed fuse, the main feature of which is the ease of replacement and maintenance of the fuse (fuse element) without the need for a complete replacement of the equipment. Below is the basic information:
Cold-shrinkable end coupling 6 kV
6KV Cold Shrink Cable Terminal is a cable accessory that is made of elastic materials (such as silicone rubber or EPDM), sealed and insulated by elastic compression force. Its main components include cold shrink tension control tube, insulating tube, branch coupling, etc. Adaptive shrinkage is achieved by removing the inner support spiral tape to match the cable interface
Fuse-(H)RW12-35kV
Specially designed for short circuit and overload protection of distribution lines and transformers, with the function of splitting and combining load currents, suitable for protecting power equipment on overhead lines and in harsh environments
disconnector-HJDW6-0.5630~2000
HJDW6 series is a low voltage fused isolation switch designed specifically for 50Hz AC distribution lines with rated voltages of 500V and below. Mainly used for short circuit, overload, open circuit and short circuit protection under no-load conditions on the low voltage side of transformers
Suspended insulator 220 kV
220 kV, suitable for high-voltage 50 Hz three-phase AC transmission systems, ensuring long-term outdoor operation. The core is made of epoxy fiberglass and the protective shell is made of high temperature vulcanized silicone rubber, reducing weight by 45-50% compared to porcelain.
End coupling ready for installation 10 kV
Using rubber and polymer composite materials with elastic memory function, it can achieve 24 cold shrinkage installation process; The temperature resistance range covers 70℃ to 200℃, with good fire resistance and adapt to various working conditions
Fuse (H)RW12-24kV
Specially designed for short circuit and overload protection of distribution lines and transformers, with the function of splitting and combining load currents, suitable for protecting power equipment on overhead lines and in harsh environments
Disconnector-(H)GW4-220kV
GW4-220 isolation switch is an open AC isolation switch designed specifically for 220kV high voltage power systems, mainly used for circuit switching and electrical isolation of equipment under no-load conditions.
End coupling ready for installation 6 kV
Using rubber and polymer composite materials with elastic memory function, it can achieve cold shrinkage installation process of 24; Temperature resistance range covers 70℃ to 200℃, with good fire resistance and adapt to various working conditions
Insulator with 1/2 eye 24 kV
Connection Design: Single Eye/Double Eye Configuration: Suitable for hanging or tension insulators, double eye design is mainly used for hanging wires, and one eye for fixed ends.
Support insulator 35 kV
35 kV, suitable for high-voltage overhead lines of three-phase alternating current with a frequency of 50 Hz. Composite crossbar: fiberglass rod and protective skirt made of silicone rubber, weight reduced by 60%, high impact resistance, hydrophobicity: the surface energy of silicone rubber is low, which allows maintaining high insulation in dirty conditions (the flashover voltage increases by 2 times when dirty).
Lightning rod 10 kV
Type classification: 10kV lightning rods mainly include power plant type, distribution type, and removable type, among which zinc oxide lightning rods have become the main ones due to their non-linear current-voltage characteristics.
