Products
Plug-in switch-GW13
GW13 series is an outdoor high voltage AC isolation switch designed specifically for 50Hz AC power systems. Mainly used to open and close circuits under no-load conditions to achieve electrical isolation or connect the neutral point of a transformer
Description
marker
Product Details
GW13 series is an outdoor high voltage AC isolation switch designed specifically for 50Hz AC power systems. Mainly used to open and close circuits under no-load conditions to achieve electrical isolation or connect the neutral point of a transformer
Modular Layout: A modular combination of brackets, bases, insulators and conductive parts to support inclined installation (eg 25° brackets).
Functions
Provide visible break points to ensure safe service.
Connecting the neutral point of the transformer to optimize the operating mode of the electrical network.
Typical Applications
- High voltage power grid: neutral point insulation in substations and power plants.
- Distribution system: 68 high voltage distribution circuit for new energy projects such as wind power and photovoltaics.
- Industrial: Power isolation and protection of heavy equipment.
Special type
High Prototype: Suitable for environments below 3000m altitude.
Anti-pollution type: Reinforced insulation design, suitable for high pollution areas.
GW13 series isolation switches, with their high reliability, low maintenance requirements and flexible adaptation, have become the key equipment for safe isolation in high-voltage power systems. The selection must be fully evaluated based on voltage level, current rating and environmental conditions.
contact us
Related Popular Products
Fuse-(H)RW5-35 kV
HRW5 series is a 35kV open high voltage fuse specially designed for short circuit and overload protection of power lines and transformers, with open circuit and low load current line opening and closing functions.
Plug-in switch-GN19-12
The GN19-12 type disconnect switch is an indoor high-voltage switching device widely used in power systems with 50 Hz alternating current and 12 kV rated voltage. Mainly used to open and close circuits under no-load conditions to achieve reliable insulation between electrical equipment and power supply. It is divided into regular type (GN19-12) and wall type (GN19-12C), and supports three-phase parallel installation or wall installation in special scenarios.
Cold-shrinkable end coupling 6 kV
6KV Cold Shrink Cable Terminal is a cable accessory that is made of elastic materials (such as silicone rubber or EPDM), sealed and insulated by elastic compression force. Its main components include cold shrink tension control tube, insulating tube, branch coupling, etc. Adaptive shrinkage is achieved by removing the inner support spiral tape to match the cable interface
Middle cold-shrinkable coupling 66 kV
Rated voltage: 66 kV, lightning impulse withstand voltage ≥ 250 kV, power frequency withstand voltage ≥ 125 kV (continuously for 30 minutes); partial discharge capacity ≤ 5 pC (complies with IEC 60840 standard).
“T” type connector
The T-plug connector is a fully insulated and sealed cable connector widely used in medium and high voltage power supply systems. Thanks to its T-shaped design, it allows for quick connection and disconnection of cables to equipment. Its main features include electrical stability and environmental adaptability. It is widely used in ring network distribution cabinets, branch cables and other systems.
Lightning rod 66 kV
Zinc Oxide Composite Type: Highly resistant to contamination, suitable for substations and power lines Performance Standard: Meets GB/T 18802.1 and IEC 60099-4 specifications
Terminal made of ceramic-silicon-rubber composite material
The composite termination (terminal) is usually installed outdoors and serves as a termination device for high-voltage cables. Its main function is to connect underground or ducted high-voltage power cables to overhead power lines or key substation equipment such as transformers and switching devices.
Disconnector-(H)GW4-220kV
GW4-220 isolation switch is an open AC isolation switch designed specifically for 220kV high voltage power systems, mainly used for circuit switching and electrical isolation of equipment under no-load conditions.
Middle cold-shrinkable coupling 33 kV
Suitable for 33kV AC three-phase systems, designed using double-layer cold-shrink silicone tube with built-in stress cone to distribute the electric field evenly, local discharge capacity ≤ 10 pC; The connection of conductors is carried out by crimping, and the copper tube is suitable for cable cross-sections from 50 to 1000 mm².
Heat-shrinkable end coupling 1 kV
1kV heat shrink cable terminal is the main component for connecting low voltage cables, suitable for insulation processing and protection of 0.6-1kV cross-linked cables. It achieves sealing and strengthening the insulation between the cable and the terminal by heating heat shrink, and has the characteristics of small size, easy installation and wide environmental adaptability
Cold-shrinkable end coupling 1 kV
Suitable for 0.6/1kV three-phase AC distribution systems, compatible with low voltage power cables (such as YJV and VV series), with a cross-sectional area of 1.5-630mm².
Suspended insulator 220 kV
220 kV, suitable for high-voltage 50 Hz three-phase AC transmission systems, ensuring long-term outdoor operation. The core is made of epoxy fiberglass and the protective shell is made of high temperature vulcanized silicone rubber, reducing weight by 45-50% compared to porcelain.
Fuse-HPRWG2-15 kV
Specially designed for 35kV power systems, it has short circuit, overload and load current switching protection functions, suitable for harsh environments such as wind farms and power lines
Plug-in connection at the rear
Appearance The overall design is T-shaped. The large port at the top is used to connect the main cable, and the perpendicular side port is used to output the branch cable. The bottom port is usually equipped with a special sealing or connecting component to ensure a reliable connection and sealing of the cable system.
Insulator with 1/2 eye 33 kV
33 kV, suitable for three-phase power lines and 50 Hz AC distribution systems, ensures long-term outdoor operation.
Middle cold-shrinkable coupling 24 kV
Conductor Connection: Uses crimping or welding technology to securely connect two cable cores, which ensures good electrical conductivity between conductors, reduces contact resistance and minimizes energy loss. The insulating layer is made of silicone rubber, which has excellent insulating properties and corona resistance. It can withstand 24 kV voltage, preventing current leakage and short circuit.
